Car keys · Vaughan
Ignition Lock Repair
The key turned the engine off in the driveway and now refuses to come back out. Wiggling it, pushing the shifter through every gear again, even leaning gently on the wheel; the barrel keeps holding on to it regardless.
Ignition Lock Repair
In plain words
Whether the key won't insert, won't turn, turns without engaging anything, or is stuck and refuses to come back out, each version of the symptom points toward a different part of the mechanism. A key that spins loosely usually means something has disconnected inside; a key that won't insert usually means the barrel or the key itself is the obstacle. Naming the exact behaviour on the phone lets the locksmith bring the right tools before ever touching the vehicle.
How the visit goesThe car arrived with one worn-looking key and a story about a lost spare. It turns the ignition, eventually, after some patience and a particular angle nobody in the household can quite describe or repeat on the first try.
Vaughan
How the visit goes
Separating a worn key from a worn cylinder
A spare key, even an old one, answers a question a single key cannot. If the spare turns the ignition smoothly while the regular key struggles, the key itself is the likely problem, rounded edges no longer lifting the internal wafers the way a crisp cut does. If both keys behave the same way in the barrel, the wear sits inside the cylinder instead. Where no spare exists, the locksmith reads the wafers directly with a decoder, which settles the question without waiting on a second key to test it.
Clearing grit, moisture and old grease
A barrel that has gone stiff from road salt, winter grit or years of old grease is opened, cleaned and treated with whatever lubricant the vehicle's own service instructions call for. Water that has found its way into the keyway is dried out fully before the cylinder is reassembled, so trapped moisture is not left sitting against the wafers to start the same problem again next season.
A record worth keeping
Whether the vehicle is yours long-term or recently purchased, a plain account of what was done to the ignition is worth holding onto: which parts were replaced, how many keys were cut, and whether the doors were brought onto the same key. It is a useful line in the vehicle's history file, and a straightforward thing to hand to an insurer, a future buyer or a mechanic who asks about it later.
Ignition Lock Repair
In the van
- Retaining pins and clips
- Steering column trim tools
- Cylinder decoder
- Keyed-alike pinning kit
- Key blanks and cutting machine
What affects the quote
Same fees day, night or weekend
1Evidence of an earlier forced attempt
A lock that shows signs of having already been forced needs a full cylinder and housing replacement rather than a simple service, since the internal parts can no longer be trusted as they stand.
2Service in place versus full replacement
Cleaning, freeing and lubricating an existing cylinder is a lighter job than removing a barrel that is cracked, seized or too worn to trust, pinning a new one, and refitting everything around it afterward.
3Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
Ignition Lock Repair: questions
What if the key won't go into the slot at all?
That points toward the barrel itself, debris packed into the keyway, or a key that has bent or worn out of shape rather than a deeper electronic problem. The keyway is checked and cleared first, the key is compared against a spare if one exists, and the barrel is serviced or replaced depending on what that first check turns up.
Can ignition lock repair get a car running again if it won't start at all?
Sometimes, and sometimes the ignition is only part of the picture. If the barrel is not turning the switch through its positions, freeing or replacing it can resolve the whole problem. If the barrel turns properly and the vehicle still stays silent, the remaining cause sits elsewhere in the electrical or fuel system, and that half of the question is named clearly rather than guessed at.
Does cold or wet weather affect an ignition cylinder?
It can. Road salt, grit and moisture from a slushy season work their way into the keyway over time, and old grease inside the mechanism can stiffen in the cold. A barrel affected this way is cleaned, dried and treated with whatever lubricant the vehicle's own service information calls for, which helps it move freely through the next stretch of similar weather ahead.
Car Keys
- Car Key ReplacementThe only key to the car went into the lake with the kayak.
- Spare Car Key DuplicationA car sits at the cottage all season, and the only key to it lives on a ring three hours away in…
- Key Fob ProgrammingThe remote clicks the way it always has, but the vehicle no longer locks, unlocks or answers with…
Ignition Lock Repair near you
Whether you own a home in Vaughan, run a shop or manage a few rental units, the lock services here are organised the way people actually ask for them. Start with the problem you have today, and read on to see what else on the door might deserve a look while a locksmith is already there.